PlugIns

Wide Selection of PlugIn Interfaces for Data Acquisition

A PlugIn is an interface between IPEmotion and any desired measuring system, control unit, or protocol. This interface supports various transport layers like Ethernet, USB, and serial communication. A Software Developer Kit (SDK) package is available for standardized PlugIn development, which can be selected in the custom or full installation.

Advantages of PlugIns

  • Every PlugIn follows the same operating logic
  • Easy-to-understand user interfaces allow you to configure measurement systems and channel parameters.Measurement data from different PlugIns is stored synchronously
  • Developers benefit from standardized SDK functions (e.g. a scaling calculator)
  • PlugIn vendors benefit from the integrated PlugIn licensing technology to generate income through software license sales

PlugIns for Automotive Applications

Description

Configuration and data acquisition (TEDS, STG, IEPE, Voltage, High Voltage, mA, RTD, TC, DIO, PWM, Encoder) using IPETRONIK measurement devices via CAN bus or X-LINK and XCP on Ethernet.
X-LINK devices Mx-SENS2 4 and Mx-STG2 6 are supporting sample rate up to 100 kHz/channel.

Vendor: IPETRONIK

Description

Configuration and data acquisition for IPETRONIK data logger based on the TESTdrive data logger software.

Supported hardware: IPElog, IPElog2, M-LOG, M-LOG V3, FLEETlog2.

Vendor: IPETRONIK

Description

ECU protocol measurement and calibration based on CCP, XCPonCAN, XCPonETH. Bus traffic analysis CAN, LIN and FlexRay and CAN traffic output simulation. Diagnostics measurements using OBD, WWH-OBD, KWP, GM-LAN, UDS, J1939. Intelligent imports for CAN dbc / XML, LDF, Fibex, FlexRay, Autosar, A2L und GM-LAN description files.

Vendor: IPETRONIK

Description

LIN bus measurement with configuration as master, slave or listener. Signals are imported via .LDF description file. The PlugIn is dedicatd to the IPEcanPRO FD hardware.

Vendor: IPETRONIK

Description

Current clamp. Konfiguration and data output via CAN bus.

Vendor: CANWAY Technology GmbH

Description

Developed for measurements on various units and HV components in vehicles or on test benches.

  • High bandwidth for DC and AC measurements > 500 kHz
  • 24 bit ADC with 15 MHz sampling rate
  • Measurement range 1000 V/1000 A
  • Designed for direct installation in the engine compartment
  • Data output via XCP-on-Ethernet, OPC UA, CAN

Vendor: IPETRONIK

PlugIns for Industrial Automation

Description

Access to Siemens S7 automation systems with different interfaces. Configurations can be created by importing STEP 7
.s7p and TIA .ap1 project files in order to select the variables of interest.

Vendor: IPETRONIK

Description

Access to the Profibus PLC network to operate in master or slave mode.

Vendor: IPETRONIK

Description

Configuration and data acquisition of Beckhoff TCP/IP field bus couplers with K bus terminals. Interfacing to TwinCAT PLCs based on EtherCAT EL-terminals is also supported.

Vendor: IPETRONIK

Description

Configuration and data acquisition via Ethernet TCP/IP field bus couplers for digital and analog signals.

Vendor: IPETRONIK

Description

Interfacing any MODBUS devices using either RTU interface (serial) or TCP interface (LAN). Supporting many function codes to set and read registers. PlugIn is licensed.

Vendor: Technikmedia

PlugIns for Highspeed DAQ Systems

Description

Data acquisition boards for dynamic applications.The PlugIn support many real-time configuration functions with the exception of the on-board FFT calculation. Automatic hardware detection is implemented.

Vendor: Goldammer

Description

Interface to QuantumX MX840 universal signal conditioning device for Current, Volt, RTD, Thermocouple and Strain Gauge measurement.

Vendor: IPETRONIK

Evaluation Kits for Students

Description

K8055 evaluation board for students. Automatic hardware detection over the USB port.

Vendor: IPETRONIK

Laboratory Devices

Description

Data recording of current, voltage and power and many characteristics from power analyzers.

Vendor: IPETRONIK

Current documentation

Further releases

Other

Description

Recording GPS data based on the NMEA standard protocol.

Vendor: IPETRONIK

Description

Recording the sound signal from the PC microphone / sound card.

Vendor: IPETRONIK

Description

Recording of video data in IPEmotion from USB web cams and IP cameras with the Real Time Streaming Protocol (RTSP).

Vendor: IPETRONIK

Description

The PlugIn summarizes various sensors that support CAN interfaces.

This includes the following devices:

  • IPEspeed for GPS measurement
  • IPEout for activation of digital and analog inputs
  • IPElambda for waste gas lambda measurement

Vendor: IPETRONIK