Service devices

Helper that make working on compressor test benches much easier

Several devices that support or reproduce activities on test benches.

 

IPEflush

High performance flushing device for refrigerant circuits and components

  • High cleaning performance even with heavy oil contamination
  • Self-sufficient flushing operation with pre-programmed processes
  • Cleaning procedure supporting a jetting pressure up to 12 bar
  • Flushing procedure using repetitive pulsations
  • Vacuum build-up with a pressure of up to 0.05 mbar
  • Automatic refrigerant recovery
  • Visual monitoring of operating pressures possible

Learn more

Device
Supported refrigerants
R134a
Jetting pressure
12 bar
Volume flow rate
42 l/h
Flushing cycles
18 / h
3 operating modes
Recovery, flushing, evacuation
Refrigerant connections
HP / LP (7/16" UNF)
Dimensions
W850 mm x H950 mm x D450 mm (33.46 in x 37.40 in x 17.71 in)
Weight
95 kg (209 lb)
Type of control
PLC system
Power consumption, typical
600 W
Number of sight glasses
2 - inlet & outlet refrigerant level
Number of pressure gauges
3
HP gauge - high pressure
-1 … 40 bar
MP gauge - medium pressure
-1 … 25 bar
LP gauge - low pressure
-1 … 15 bar
Working temperature range
Max. 40 °C (104 °F)
Oil collector
700 ml
Electrical connections
Power supply
1 x 16 A, 230 VAC, 50 Hz Schuko
Vacuum pump
Minimum pressure
0.05 mbar

IPEcharge

Filling station

  • Exact dosage of the filling amount with needle valve
  • Integratet mass flow meter for determination of filling amount
  • Counter for monitoring and storing filling amount
  • With integrated heating pad for quick filling process
  • Service-outlet to interface external devices
  • Filling station will be delivered without a CO2 refrigerant bottle

Learn more

Device
Supported refrigerants
R744 (CO2)
Refrigerant connections
7/16" UNF
Connection bottle pressure reducer
B540 mm x H950 mm x T600 mm (21.26 in x 37.40 in x 23.62 in)
Weight
Approx. 20 kg / 44 lb (without bottle))
Power consumption, typical
Ca. 300 W
Number of pressure gauges
2
Working temperature range
Max. 40 °C (104 °F)
Connection bottle pressure reducer
Compression fitting
Content gauge (on pressure reducer)
0 … 315 bar
Working pressure gauge (on pressure reducer)
0 … 100 bar
Electrical connections
Power supply
1 x 16 A, 230 V AC, 50 Hz Schuko
Supply
Refrigerant bottle
Adaptation to customer requirements
Control ranges
Working pressure gauge (on pressure reducer)
0 ... 60 bar

IPEsim

Module for simulation of automotive cooling-water circuits

  • Simulating of heat sink and heat source, e.g. battery heat loss
  • Automatic control of process variables: cooling and heating capacity, flow temperature, volume flow, system pressure, pressure drob flow
  • Operating via master computer and possible integration of IPEmotion
  • Integrated PLC system with touch panel
  • Available different test circuit volumes

Learn more

Device
Supported coolants secondary brine
Depending on customers requirements
Connections main brine
Inlet (1") / outlet (1") - outside thread
Connections secondary brine
Inlet (1") / outlet (1") - outside thread
Service connections
3/4" (3 x for flushing, filling and draining)
Dimensions
W2000 mm x H2000 mm x D750 mm (78.75 in x 78.75 in x 29.53 in)
Weight
500 kg (1102 lb)
Type of control
PLC-controlled / touch panel or master computer
Power consumption, typical
Max. 30 kW
Working temperature range
Max. 40 °C (104 °F)
Electrical connections
Power supply
1 x 32 A, 400 V AC, 50 Hz
Supply
Supported coolants
Brine (40 % water/ 60 % glycol)
Flow temperature recooling fluid
-35 … 6 °C (-31 … 43 F)
Volume flow recooling fluid
1700 l/h
Compressed air
5 bar < p < 16 bar
Control ranges
Cooling capacity
0 … 7.5 kW
Heating capacity
0 … 18 kW
Temperature range
-27* … 120 °C (-17* … 248 F)
Volume flow
300 … 3000 l/h
Pressure drop flow
0 … 4.5 bar
System pressure
0 … 2.5 bar
Note
* depending on flow temperature recooling fluid