| Measurement input DMS |
| Messbereich Dehnmessstreifen |
±2 V in strain gauge measuring mode |
| Accuracy at ambient temperature 25 °C |
±0.075 % + 7 µV corresponding to the selected measuring range 3 |
| Special functions |
Shunt resistance simulation 5 ... 200 kΩ, Bridge adjustment, Internal bridge completion, Resistance for bridge completion 120, 350, 1000 Ω, Shuntcheck, also during measurement |
| Channel volt |
| Measurement range SENS |
±0.01 / 0.02 / 0.05 / 0.1 / 0.2 / 0.5 / 1 / 2 / 5 / 10 / 20 / 50 V |
| Accuracy at ambient temperature 25 °C |
0.075 % of selected measurement range |
| Input HV |
| * Safety instructions |
|
| Measurement input IEPE |
| Filtergrenzen (Hochpass) |
0.1 ... 16 kHz (accuracy 20%) |
| Leerlaufspannung |
24 V |
| General channel properties |
| AD converter |
16 bit / SAR (successive approximation register) |
| Oversampling |
40 kHz |
| Channel sampling rates |
1 / 2 / 5 / 10 / 20 / 50 / 100 / 200 / 500 Hz, 1 / 2 / 5 / 10 / 20 / 40 kHz (CAN up to 2 kHz) |
| Aggregate sample rate |
320 kHz |
| Hardware filter (switchable) |
Butterworth (8-pole), 4.8 kHz cut-off frequency, Accuracy 10 % |
| Hardware filter (fixed) |
Accuracy 25 %, Typ RC 2-Pol, 17 kHz Cut-off frequency |
| Software filter types |
Butterworth, Elliptic (8-pole), Bessel |
| Channel impedance |
10 MΩ (differential), 5 MΩ (mass-related) |
| Software filter (DSP selectable) |
50/ 66.67/ 100/ 125/ 166.67/ 250/ 500/ 667 Hz, Accuracy 0.05 %, 1.0 / 1.25 / 1.67 / 2.5 / 5.0 / 6.67 / 10 / 12.5 / 16.67 kHz, 1.0/ 1.25/ 1.67/ 2.5/ 5.0/ 6.67/ 10/ 12.5/ 16.67/ 25 Hz |
| Channel LED |
Yes, Channel LED is flashing during configuration, Yes, Sensor break detection, In case of overcurrent of sensor supply |
| TEDS |
Class 2 |
| Channel CNT |
| Number of inputs |
|
| Excitation |
| Sensor excitation ranges |
Unipolar 0.5 / 1.25 / 2.5 / 5 / 10 / 12 / 15V, STG Bipolar ±0.5/ ±1.25/ ±2.5/ ±5 V, Bipolar ±0.5 / ±1.25 / ±2.5 / ±5 / ±10 / ±12 / ±15 V |
| Sensorspeisung |
, ±0.5/ ±1.25/ ±2.5/ ±5 V |
| Accuracy excitation at ambient temperature 25 °C |
0.5 %, 0.1 % |
| Drift for ambient temperature -40 … 85 °C |
±30 ppm/K |
| Sensor Anschluss |
4-wire, 6-wire |
| Galvanic isolation |
| Input ↔ module power supply |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Input ↔ CAN |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Input ↔ enclosure |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Input ↔ input |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Device |
| Inputs |
8 |
| Genauigkeiten |
|
| Maximum input protection voltage (channel) |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Voltage supply |
9 … 36 VDC |
| Supply voltage thresholds |
On 9 ±0.3 VDC / Off 6 ±0.3 VDC |
| Power consumption, typical |
7.5 W (all excitations off) |
| Working temperature range |
-40 … 85 °C (-40 … 185 °F) |
| Storage temperature range |
-55 … 105 °C (-67 … 221 °F) |
| IP-Code |
IP 54 (ISO 20653 - 2013) |
| Relative humidity |
5 ... 95 % |
| Dimensions |
W75 mm x H119 mm x D185 mm (2.95 in x 4.69 in x 7.28 in) |
| Weight |
1430 g (3.15 lb) |
| Configuration interface |
Ethernet |
| Data transfer rate |
100 Mbit Ethernet (IEEE 802.3) |
| Housing material |
Aluminium, black powder coated |
| Input sockets |
Lemo EGG 1B 307 (7-Pin), Lemo EGG 2B 310 (10-pin) for TEDS |
| Status LED |
Yes |
| Schutz gegen aggressive Flüssigkeiten |
|
| Electrical data |
| Status LED |
|
| Accessories |
| System cable |
630-500, X-Link-TERM, 630-302, 630-504, USB2ETH-XLINK, X-Link-DEF, 630-522, 630-505, 630-501, 630-507, 630-524 |
| Input cable |
600-747, 600-760, 600-850 |
