| Channel volt |
| Measurement range SENS |
±0.01 / 0.1 / 0.2 / 0.5 / 1 / 2 / 5 / 10 / 20 / 30 / 50 / 100 V |
| Accuracy at ambient temperature 25 °C |
±0.10 % (unipolar measurement ranges), ±0.06 % (bipolar measurement ranges) |
| Input HV |
| * Safety instructions |
|
| Channel current |
| Measurement range |
0 … 20 mA, ±20 mA |
| Accuracy at ambient temperature 25 °C |
±0.40 % |
| Internal shunt resistor |
50 Ω |
| General channel properties |
| AD converter |
16 bit / SAR (successive approximation register) |
| Special functions |
Offset adjust, during measurement, multiple groups |
| Oversampling |
10 kHz |
| Channel sampling rates |
1 / 2 / 5 / 10 kHz (CAN up to 2 kHz), 1 / 2 / 5 / 10 / 20 / 50 / 100 / 200 / 500 Hz |
| Aggregate sample rate |
80 kHz |
| Hardware filter (switchable) |
Butterworth (8-pole), Accuracy 10 %, 1.2 kHz cut-off frequency |
| Hardware filter (fixed) |
5 kHz Cut-off frequency, Accuracy 25 %, Typ RC 4-Pol |
| Software filter types |
Butterworth, Elliptic (8-pole), Bessel |
| Channel impedance |
10 MΩ |
| Software filter (DSP selectable) |
100/ 125/ 166.67/ 250/ 500/ 667.67 Hz, Accuracy 0.05 %, 1.0 / 1.25 / 1.67 / 2.5 / 5 / 6.67 / 10 / 15 / 16.67 / 25 / 50 / 66.67 / 100 / 125 / 166.67 kHz, 1.0 / 1.25 / 1.67 / 2.5 / 3.34 kHz |
| Channel LED |
Yes, Yes, In case of overcurrent of sensor supply, Channel LED is flashing during configuration |
| TEDS |
Class 2 |
| Channel CNT |
| Number of inputs |
|
| Excitation |
| Sensor excitation ranges |
Bipolar ±2.5 / ±5 / ±7.5 / ±8 / ±10 / ±12.5 / ±15 V |
| Sensorspeisung |
|
| Accuracy excitation at ambient temperature 25 °C |
±0.25 % |
| Accuracy excitation at ambient temperature 85 °C |
±0.40 % |
| Drift for ambient temperature -40 … 85 °C |
±40 ppm/K |
| Sensor excitation current |
45 mA (for V output ±7.5 / ±15.0 V), 40 mA (for V output ±5.0 / ±12.5 V), 30 mA (for V output ±2.5 / ±10.0 V |
| Galvanic isolation |
| Input ↔ module power supply |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Input ↔ CAN |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Input ↔ enclosure |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Input ↔ input |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Input ↔ excitation |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Device |
| Inputs |
8 |
| Precisions |
|
| Maximum input protection voltage (channel) |
±100 V (indefinitely), ±200 V (short-time, t < 2 ms) |
| Voltage supply |
9 … 36 VDC |
| Supply voltage thresholds |
On 9 ±0.3 VDC / Off 6 ±0.3 VDC |
| Power consumption, typical |
4.0 W (all excitations off) |
| Working temperature range |
-40 … 85 °C (-40 … 185 °F) |
| Storage temperature range |
-55 … 105 °C (-67 … 221 °F) |
| IP-Code |
IP 67 (ISO 20653 - 2013) |
| Relative humidity |
5 ... 95 % |
| Dimensions |
W212 mm x H41 mm x D55 mm (8.35 in x 1.61 in x 2.17 in) |
| Weight |
690 g (1.52 lb) |
| Configuration interface |
Ethernet |
| Data transfer rate |
100 Mbit Ethernet (IEEE 802.3) |
| Input sockets |
Lemo EGG 1B 307 (7-Pin) |
| Status LED |
Yes |
| Schutz gegen aggressive Flüssigkeiten |
|
| Electrical data |
| Status LED |
|
| Accessories |
| System cable |
630-500 X-Link system cable, 630-528 X-Link cabe, ETH RJ45/PWR banana/ for M3 integration, 630-302 X-Link system cable ES ETH LEMO 1B8p, 630-504 X-Link cable M-CAN, 630-522 X-Link system cable PC RJ45 (galv), 630-501 X-Link cable PWR banana, 630-505 X-Link PWR cable X-Link-CAN/M-CAN, 630-507 X-Link cable M-LOG PR08 ETH, 630-524 X-Link system cable LOG X-Link |
| Input cable |
670-810, 620-674 M-SENS LEMO 1B6p I-measure cable open, 670-811, 670-807, 600-866 SENS LEMO 1B7p cable BNC/P, 600-731 SENS LEMO1B7p cable banana |
