SIM-Series

measuring modules with IP54 enclosure SIM-Series for mobile applications (test drive) measuring inputs for temperature, voltage, current, strain gauge, counter functions, bus data like CAN, LIN, K-Line bus data acquisition also via protocols CCP, KWP, McMess, J1939 measuring inputs with complete galvanic isolation output of 16 Bit measuring data to CAN -40 °C to +85 °C ambient temperature 9 V DC to 36 V DC supply voltage interfaces/drivers for common used application software like: Vehicle Spy 3 from ICS CANape or CANalyzer from Vector INCA from ETAS DIAdem or LabVIEW from National Instruments CalDesk from dSPACE VISION from ATI Accurate Technologies DTECS from Volvo

	SIM-VIN
	SIM-SENS / T-SENS
	SIM-STG
	SIM-CNT / T-CNT
	SIM-THERMO 16 / T-THERMO 16
	SIM-THERMO 8
	SIM-PT100 / SIM-PT200
	SIM-ECU
	SIM-VOUT / T-VOUT
	SIM-LAMBDA / T-LAMBDA

• 8 analog inputs for voltage/ current
• voltage up to 60 V, current up to 20 mA
• 5 bipolar measuring ranges
• channel sampling rates up to 1 kHz

• 8 analog inputs for voltage/ current
• voltage up to 60 V, current up to 20 mA
• 5 bipolar measuring ranges
• separate sensor supply for each input
• channel sampling rates up to 1 kHz

• 8 measuring inputs, each supporting 4 different signals
• strain gages (1/4, 1/2, 1/1 bridges, shunt calibration)
• sensors with analog output (excitation up to +/-15 V, 60 mA)
• differential voltage
• ICP sensors
• channel sampling rates up to 5 kHz

• 4 voltage comparator inputs up to +/- 10 V
• free adjustabel ON/OFF thresholds for signal evaluation
• frequency measurement up to 2,5 MHz
• separate sensor supply for each input
• each input socket also provides an analog output and 2 additional TTL inputs
• channel sampling rates up to 1 kHz

• 16 thermocouple inputs type K
• with cold junction compensation
• measuring range -60 to +1370 °C
• miniature thermo and also Sub D sockets available
• channel sampling rates up to 10 Hz

• 8 thermocouple inputs type K resp. type N
• with cold junction compensation
• measuring range -60 to +1370 (1300)  °C
• miniature thermo input sockets
• channel sampling rates up to 10 Hz

• 8 PT 4-wire temperature inputs
• modules for PT100 and also PT200 available
• measuring range -50 to +450 °C
• channel sampling rates up to 50 Hz

• measuring inputs for CAN bus and serial data
• 1 x CAN High/Low Speed, 1 x CAN High Speed
• 1 x RS232 also for GPS data via NMEA protocol

• 4 measuring inputs for bus data
• CAN High/Low, CAN High, CAN Comfort, K-Line, LIN
• protocols CCP, KWP2000, KWPonCAN optional
• measuring rates per channel up to 1 kHz

• CAN-Analog converter to adapt devices without a CAN interface
• read CAN messages via CAN High Speed interface optional via High/ Low Speed interface (CAN H/L)
• 8 analog voltage outputs up to +/- 10 V
• measuring rates per channel up to 1 kHz

• measuring data coordinator for SIM modules
• management of the CAN data transmission
• supporting synchronous data acquisiton
• total sampling rate up to 16 kHz

• 4 combined measuring inputs
• for broad-band Lambda sensors, e.g. from Bosch
• import of new characteristic lines via CSV file
• upgradeable for new types of Lambda sensors
• channel sampling rates up to 1 kHz